Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 5:15 pm
Brand new g19 has a crunch well ahead of the trigger break. I found these burrs. Any ideas?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Kentucky Armory Club
For firearms enthusiasts from lovers of Glock, AR-15, XD, 1911s, shotguns, AK-47s, to black powder. For shooters, hunters, LEO'S, military, or casual enthusiasts. KAC is about firearms, and all the good things in life. Welcome!
https://www.kentuckyarmoryclub.com/
Gen 4 g19 - not perfect
https://www.kentuckyarmoryclub.com/viewtopic.php?f=71&t=21296
Page 1 of 1
Re: Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 5:33 pm
It's brand new? I don't care what the cause is, my brand new G19 would go back to Glock.
Re: Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 7:24 pm
I hate to be "that guy", but this looks like damage from improper takedown. Looks like someone manually pulled the striker back with the slide off the frame and let the striker repeatedly hit the pin with full force.
Re: Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 7:25 pm
Same thoughts.Rescue9 wrote:I hate to be "that guy", but this looks like damage from improper takedown. Looks like someone manually pulled the striker back with the slide off the frame and let the striker repeatedly hit the pin with full force.
Re: Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 7:34 pm
Return for repair or replace part
Re: Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 7:35 pm
You can smooth out burrs but that is not the crutch you seek
Re: Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 9:31 pm
Buy another and put in. Probably cheaper than shipping gun back in and the annoyance of down time.
Sent from my SAMSUNG-SM-G870A using Tapatalk
Sent from my SAMSUNG-SM-G870A using Tapatalk
Re: Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 10:04 pm
Did you let cranky get hold of it ?? 
Re: Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 11:04 pm
Buy an Apex Tactical plunger. Nice improvement
Re: Gen 4 g19 - not perfect
Posted: Sun Dec 18, 2016 11:57 pm
A new plunger is great assuming something in the gun didn't do that to the factory one
Re: Gen 4 g19 - not perfect
Posted: Mon Dec 19, 2016 4:52 pm
The only way I could see that happening is if the striker isn't catching on the trigger release bar. But if this was the case, the owner should know it as the gun wouldn't fire after a round was chambered.ssracer wrote:A new plunger is great assuming something in the gun didn't do that to the factory one
Re: Gen 4 g19 - not perfect
Posted: Mon Dec 19, 2016 5:29 pm
Yeah I of course was assuming that he had it down that far that he would have seen the other damage if in fact damage was incurred.ssracer wrote:A new plunger is great assuming something in the gun didn't do that to the factory one
Sent from my SAMSUNG-SM-G870A using Tapatalk
Re: Gen 4 g19 - not perfect
Posted: Tue Dec 20, 2016 6:20 pm
AgreedToddstang wrote:Same thoughts.Rescue9 wrote:I hate to be "that guy", but this looks like damage from improper takedown. Looks like someone manually pulled the striker back with the slide off the frame and let the striker repeatedly hit the pin with full force.
Re: Gen 4 g19 - not perfect
Posted: Tue Dec 20, 2016 9:24 pm
Imo it takes a few hundred rounds to break in a glock trigger. I dont subscribe to the whole modified triggers on carry guns, the factory glock trigger is great.
Re: Gen 4 g19 - not perfect
Posted: Fri Dec 30, 2016 10:38 am
I found it. A little burr in the frame was catching on the trigger safety. I smoothed that out and the click is gone.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Gen 4 g19 - not perfect
Posted: Fri Dec 30, 2016 10:41 am
The pistol ran fine. But it was a noticeable out of place crunch. I would have taken it back but I couldn't stand to be without her.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk