M92 PAP Pistol

SBR goes here. Have questions about trusts, gas systems, draco's, etc, ask away.
Smithengineered
Posts: 470
Joined: Wed Feb 06, 2013 6:48 pm
Location: Louisville
Has liked: 6 times
Been liked: 4 times

M92 PAP Pistol

Post by Smithengineered » Sat Feb 28, 2015 10:36 am

Has anyone on here SBR'd a M92 pistol? I'm looking at doing this in the near future, but wondering if I need to swap out the trunnion? I'm going with a stormwerkz folding mechanism. Looking at the inside of this does not look like it has much meat to hold a stock....
Top
User avatar
jmeister
KAC Member
KAC Member
Posts: 1078
Joined: Sat Mar 03, 2012 8:26 pm
Location: Lexington
Has liked: 3 times
Been liked: 3 times

Re: M92 PAP Pistol

Post by jmeister » Sat Feb 28, 2015 11:24 am

Seen quiet a few just drill & tap the rear trunnion. That's how I did my Draco, dunno if the thickness is similar or not to the PAP. I'm not planning on doing pull ups with it or breaking off doorknobs though either.
Top
Smithengineered
Posts: 470
Joined: Wed Feb 06, 2013 6:48 pm
Location: Louisville
Has liked: 6 times
Been liked: 4 times

Re: M92 PAP Pistol

Post by Smithengineered » Sat Feb 28, 2015 1:43 pm

jmeister wrote:Seen quiet a few just drill & tap the rear trunnion. That's how I did my Draco, dunno if the thickness is similar or not to the PAP. I'm not planning on doing pull ups with it or breaking off doorknobs though either.
I looked in my Draco and it's much beefier than my M92. Same here on not trying to do any heavy duty stuff with it.
Top
guncrank1
KAC Member
KAC Member
Posts: 6384
Joined: Sat Mar 03, 2012 8:48 pm
Location: Metro Louisville
Has liked: 3 times
Been liked: 15 times
Contact:
Contact guncrank1

Re: M92 PAP Pistol

Post by guncrank1 » Sat Feb 28, 2015 6:55 pm

Change the turrion
May require holes welded up though.
Top
User avatar
kokopelli
KAC Member
KAC Member
Posts: 3611
Joined: Sun Mar 04, 2012 4:14 pm
Has liked: 1 time
Been liked: 17 times

Re: M92 PAP Pistol

Post by kokopelli » Sat Feb 28, 2015 7:38 pm

easiest/cheapest sbr on those is the VZ58 side fold stock, that has the single, large threaded screw. Drill and tap on the rear end....bam.

Check out Meridian...they did one this way. Pics are on here somewhere...
Top
User avatar
kokopelli
KAC Member
KAC Member
Posts: 3611
Joined: Sun Mar 04, 2012 4:14 pm
Has liked: 1 time
Been liked: 17 times

Re: M92 PAP Pistol

Post by kokopelli » Sat Feb 28, 2015 7:40 pm

here ya go:

http://kentuckyarmoryclub.com/viewtopic ... 36&t=14826
Top
Smithengineered
Posts: 470
Joined: Wed Feb 06, 2013 6:48 pm
Location: Louisville
Has liked: 6 times
Been liked: 4 times

Re: M92 PAP Pistol

Post by Smithengineered » Sat Feb 28, 2015 8:30 pm

guncrank1 wrote:Change the turrion
May require holes welded up though.
That's the answer I was afraid of lol
Top
Smithengineered
Posts: 470
Joined: Wed Feb 06, 2013 6:48 pm
Location: Louisville
Has liked: 6 times
Been liked: 4 times

Re: M92 PAP Pistol

Post by Smithengineered » Sat Feb 28, 2015 8:32 pm

Thanks. Looks decent, but I'm a bigger fan of this lol
ImageUploadedByTapatalk1425173516.469248.jpg
Top

Return to “Short-barreled Rifles”

×