Kentucky Armory Club

I belonged to a club over 20 yrs up north that was highly active in all the clays sports, I seen and shot kreigoffs, perrazzis, etc., etc., good few high rollers with all kinds of contraptions for breaking clays, but browning and berreta over unders were the lions share whether sporting, trap, or sk...

Niceguy wrote:I bet that's 1 in a billion odds...

I use to retrieve the round same way, One of the match rso's where i used to shoot idpa claimed he saw this happen twice, and didn't allow it. He did travel quite a bit for different shoots, and I believe him.

Thanks all

Yep, still,have a 512.a65 to claim. Probably get an aimpoint pro to replace it.

I don't see one listed as stock inventory, but I am pretty sure theses guys can accomodate you and know exactly what you are wanting to do.
http://www.cncwarrior.com/category-s/1950.htm

I am not saying it won't work. I am saying it won't be perfect. Minor diameter for your metric thread is 12.5 mm, the half inch threads are allready at 12.7 mm. You will have about .008 oversize (8 thou) and .004 of threads showing in wall of bore, that are 28 tpi, your 1mm pitch is 25.4 threads per...

I remember most of that stuff, being a teenager it didn't phase me much, but even most adults back then just shrugged it off and went about their business. Hearst prob got the most press and conversation, along with the PLO taking hostages at munich olympics.

http://www.thetimestribune.com/news/firearms-center-and-indoor-gun-range-set-to-open-friday/article_1327a544-f25b-11e6-bfc5-d7b152775634.html Opens Friday, called Center Target. Looks well done, 12 Lanes, rentals, sales, and a kitchen. I prob won't spend much time there cuz I have my own range, unle...

Looks like some Senetors are trying to kill SB7. Urge folks to make a call allowing a vote.
" Please call Senate President Robert Stivers II at 502-564-3120 and urge him to reverse course and bring SB 7 to the Senate floor for a vote"

The scary part is once a convention gets a go ahead, any kind of resolution can be introduced and voted on, if it gets the votes it is law of the land, and only another convention can change it. Seems like playing with dynamite to me.

Lots of interesting reading there, first time ever I heard of anyone from ATF coming out and actually saying a lot of their regulations and opinions do little to impact the publics safety. While we all just shook our heads at the useless micromanaging and prohibitions, some that work there must do t...

I like the idea of an adjustable gas block with a reference mark on what the standard volume is. That would allow for experimenting, then components could be swapped out to get to where you want to be for reliability.

Do they make adjustable gas blocks for those?

I remember the first glock i ever seen, a G17 at my local gun store. Swore I would never buy one, steel and wood is a gun, not plastic. Years later finally bought a g26 because I wanted a small gun with high capacity. I have other pistols that I like and shoot better, but carry a glock mostly. Like ...

Learn something new every day. Good stuff

Absolutely they will cut clean, I do give a few points to plasma here but definitely not a short run fabrication issue. Both will probabbly warrant dressing sharp edges with the grinder anyhow. If you tinker with other stuff, work on your own vehicle, etc., a torch setup is a handy tool to have.

Yep, when all else fails break out the fire wrench. Lol

Don't discount the value of owning an oxy acetylene outfit, much more versatile than a plasma cutter and the haz isn't bad if you use the correct tip, and don't hang around. I have both but I would lose the plasma before I would give up the torch.

My bad, see above.

Deleted opposition to this years Carry Bill. See above post of explanation.

I owe everyone an apology here. I mistakingly interpreted this years bill to allow towns to create no gun zones. My understanding was all prohibited places were by uniform, State Statute, and listed in that statute. My current understanding is that towns allready have the power to create ordinance a...

I seen barrel clamp light brackets somewhere, or figure how to screw on a rail section to that stock and use a light bracket that mounts to a rail.

https://www.congress.gov/bill/115th-con ... l/367?r=21

Well hoping this and a lot of other good legislation passes.
On that note, where is the best place in Kentucky to purchase a supressor, or two, or three?

I can vouch for the olight m2x-ut, great light, impressive spot and easily rifle mounted. In case you need a good simple charger too, check out a xtar vp2, pleased with mine so far, after my i4 tits upped. Edit: ilumn had the light for sixty bucks, backordered now, but new version is one o nine, i h...

Single point in a lathe? 11 degree?